Tianhui Machine Co.,Ltd

December 03, 2022

Application of Delta VE series inverter in CNC machining center (5)

The deceleration time measured during deceleration from 590hz to 0hz is 5.1s, and the maximum bus voltage during deceleration is 740VDC. The figure is shown in Figure 5.

Δείτε περισσότερα >>

December 02, 2022

Stone shaped machining CNC system uses technology to light stone

Multi-function CNC machining center is used to process all kinds of portrait sculptures, cylindrical sculptures, irregular stigmas, column seats and other stone three-dimensional shaped products,

Δείτε περισσότερα >>

December 01, 2022

The application of Delta VE series inverter in CNC machining center (4)

Pulse control currently offers two modes: speed mode and position mode. When working in speed mode, only need to

Δείτε περισσότερα >>

November 30, 2022

The application of Delta VE series inverter in CNC machining center (3)

Run using the panel. First, F=550, after running, it is found that regardless of the starting process or the stopping process, when the output frequency reaches about 450HZ, it does not change acc

Δείτε περισσότερα >>

November 29, 2022

The application of Delta VE series inverter in CNC machining center (2)

3.3 Inverter parameter design steps (1) Set the motor parameters to the inverter for dynamic auto-tuning of the motor. In order to play the high performance of the VE series inverter, acc

Δείτε περισσότερα >>

November 28, 2022

Influence of tool edge arc on machining of CNC lathe

1 Introduction In the process of using the CNC lathe, in order to reduce the roughness of the surface of the workpiece to be processed, reduce the tool wear and improve the tool l

Δείτε περισσότερα >>

November 27, 2022

Tool selection and cutting amount determination in CNC machining (2)

3. Selecting tools for CNC milling In CNC machining, the flat-end end mills for milling the inner and outer contours of plane parts and the milling plane are commonly used. The empirical data of t

Δείτε περισσότερα >>

November 26, 2022

Application of Delta VE Series Inverter in CNC Machining Center

Abstract: This paper mainly introduces the use of Delta VE inverter in CNC machining center. Key words: CNC machining center positioning VE inverter Delta pulse

Δείτε περισσότερα >>

November 25, 2022

Determination of tool selection and cutting amount in CNC machining

Abstract: The remarkable feature of modern knives is the rapid development of structural innovation. With the continuous expansion of the field of computer applications, mechanica

Δείτε περισσότερα >>

November 24, 2022

Research on CNC machining process simulation system (2)

1.4 Establishment of object classes Because there are many models of CNC machine tools, and their functions and structures are different, it is a time-consuming and laborious task to analy

Δείτε περισσότερα >>

November 23, 2022

Application of superhard tools in machining hard and brittle materials (2)

Third, the cutting of hardened steel The CBN-L, cBN-W and diamond composite blade PCD-D are used to turn the hard tool steel T10A (HRC60~63), and -L, -W, -D respectively represent

Δείτε περισσότερα >>

November 22, 2022

Application of superhard tools in machining hard and brittle materials (figure)

Introduction <br> <br> a certain machine parts manufacturing process using a hard material. These include some high-hardness brittle materials. In this machining field, s

Δείτε περισσότερα >>

November 21, 2022

Graphical automatic programming of CNC wire cutting 3B machining instructions (4)

3 Conclusion Practice has proved that when

Δείτε περισσότερα >>

November 20, 2022

Tool compensation system in CNC system of full-function CNC machine tools (2)

2. Machining center, CNC milling machine tool compensation The machining center and the numerical control system of the CNC milling machine, the tool compensation function includes tool co

Δείτε περισσότερα >>

November 19, 2022

Graphical automatic programming of CNC wire cutting 3B machining instructions (3)

Figure 3 Arc projection length J calculation (when left is G=G x , right is G=

Δείτε περισσότερα >>

November 18, 2022

Graphical automatic programming of CNC wire cutting 3B machining instructions (2)

Below is the entity group code for a line: (-1.<Entity name: 60000014>) (0."LINE") (8."0") (10 1.0 2.0 0.0) (11 6.0 6.0 0.0)

Δείτε περισσότερα >>

November 17, 2022

Tool compensation system in CNC system of full-function CNC machine tools

First, the proposed tool compensation With the end mill machining the workpiece on the CNC machine, it can be clearly seen that the tool center motion gauge does not coinc

Δείτε περισσότερα >>

November 16, 2022

Graphical automatic programming of CNC wire cutting 3B machining instructions

Abstract: Based on Auto CAD, a graphical automatic programming system for CNC wire cutting 3B machining instructions was developed. It uses AutoLisp language to read

Δείτε περισσότερα >>

November 15, 2022

Commonly used route for machining parts on CNC lathes (2)

(3) Analysis of axial feed distance during threading (4) An

Δείτε περισσότερα >>

November 14, 2022

Commonly used route for machining parts on CNC lathes

Commonly used route for machining parts on CNC lathes: (1) Analysis

Δείτε περισσότερα >>

November 13, 2022

The characteristics of CNC machining technology

CNC machining technology is an application technology that is continuously developed and gradually improved with the generation of CNC machine tools. The research object is the integrated tech

Δείτε περισσότερα >>

November 12, 2022

Application Research of CNC Machining Simulation System Software in Numerical Control Teaching and Identification

Fourth, the application of CNC machining simulation system in the identification of vocational skills The numerical control operator is divided into two major contents

Δείτε περισσότερα >>

November 11, 2022

Application Research of CNC Machining Simulation System Software in Numerical Control Teaching and Identification

(2) Application method of CNC machining simulation system: How to use this software for teaching, we mainly explore and practice from the following aspects in teaching. 1. Flex

Δείτε περισσότερα >>

November 10, 2022

CNC machining process analysis of parts (2)

(2) Process analysis of parts drawing The analysis and research of the part drawing is mainly to carry out the process review of the parts, such as checking the view of the design draw

Δείτε περισσότερα >>